Elo Entuitive Touchmonitor
User Guide
For 12.1" LCD Kiosk Touchmonitors
1247L Series
Revision A
Copyright © 2003 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
iii
Table of Contents
Introduction
1
Troubleshooting
17
Product Description . . . . . . . . . . . . . . . . 1
Precautions . . . . . . . . . . . . . . . . . . . . 1
About the Product . . . . . . . . . . . . . . . . . 2
Solutions to Common Problems . . . . . . . . 17
Native Resolution
19
21
Installation and Setup
3
Unpacking Your Touchmonitor. . . . . . . . . . . 3
Product Overview . . . . . . . . . . . . . . . . . 4
Main Unit . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . 4
Touch Interface Connection . . . . . . . . . . . . 5
Installing the Driver Software . . . . . . . . . . . 6
Installing the Serial Touch Driver. . . . . . . . 7
Installing the Serial Touch Driver for Windows
XP, 2000, Me, 95/98 and NT 4.0 . . . . . . 7
Installing the Serial Touch Driver for MS-DOS
and Windows 3.1 . . . . . . . . . . . . . . 8
Touchmonitor Safety
Care and Handling of Your Touchmonitor. . . . 22
Technical Specifications
23
Display Modes . . . . . . . . . . . . . . . . . 23
Touchmonitor Specifications . . . . . . . . . . 24
AccuTouch Touchscreen Specifications . . . 25
. . . . . . . . . . . . . . . . 26
Mounting Options
Hoizontal Mount . . . . . . . . . . . . . . . 26
Vertical Mount . . . . . . . . . . . . . . . . 27
No BracketMount. . . . . . . . . . . . . . . 28
Operation
31
35
9
About Touchmonitor Adjustments . . . . . . . . . 9
Controls and Adjustment . . . . . . . . . . . . 12
OSD Menu Functions . . . . . . . . . . . . 12
OSD Control Options. . . . . . . . . . . . . 13
Brightness. . . . . . . . . . . . . . . . . 13
Contrast . . . . . . . . . . . . . . . . . 13
37
. . . . . . . . . . . . . . . . . . . 13
Color
Auto Tune . . . . . . . . . . . . . . . . . 13
Frequency . . . . . . . . . . . . . . . . 14
Phase . . . . . . . . . . . . . . . . . . . 14
Track . . . . . . . . . . . . . . . . . . . 14
Text/GRP
Horizontal
. . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . 15
. . .
. .
Vertical
. . . . . . . . . . . . . .
. . .
.
15
Language. . . . . . . . . . . . . . . . . . 15
Recall
Save Exit
Cancel Exit
. . . . . . . . . . . . . . . . 15
. . .
. . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . 15
. . . .
v
C H A P T E R
1
CHAPTER 1
INTRODUCTION
Product Description
Congratulations on your purchase of an Elo TouchSystems Entuitive
touchmonitor. Your new touchmonitor combines the reliable performance of
Elo’s touch technology with the latest advances in LCD display design. This
combination of features creates a natural flow of information between a user
and your touchmonitor.
This LCD monitor incorporates 12.1” color active matrix thin-film-transistor
(TFT) liquid crystal display to provide superior display performance. A
maximum resolution of SVGA 800x600 is ideal for displaying graphics and
images. Other outstanding designs that enhance this LCD monitor’s
performance are Plug & Play compatibility, and OSD (On Screen Display)
controls.
NOTE Some monitors do not have the touchscreen capability.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
1-1
About the Product
Your LCD Desktop Touchmonitor is a 12.1” SVGA TFT color display with the
following features:
• High contrast color TFT LCD display support resolution up to SVGA
800x600. Compatible with IBM VGA and VESA.
• Power management system conforms to VESA DPMS standard.
• Universal power adapter.
• Supports DDC1/2B for Plug & Play compatibility.
• Advanced OSD control for picture quality adjustment.
• VESA lat panel monitor physical mounting inerface(75mm)
• Optional touch screen function.
For full Product Specifications refer to Appendix C.
1-2 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
C H A P T E R
2
CHAPTER2
INSTALLATION AND SETUP
This chapter discusses how to install your LCD touchmonitor and how to install
Elo TouchSystems driver software.
Unpacking Your Touchmonitor
Check that the following 9 items are present and in good condition:
Serial cable
VGA cable
European power cable
Brick power supply
CD and Quick Install
Guide
Power cable US/Canada
OSD Remote
2-3
Product Overview
Main Unit
Rear View
2-4 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
Touch Interface Connection
NOTE: Before connecting the cables to your touchmonitor and PC, be sure that the computer
and touchmonitor are turned off.
1 Connect one end of the power adapter to the monitor and the other end to
the connector of the power cord.
2 Connect one end of the video cable to the rear side of computer and the other
to the LCD monitor. Tighten by turning the two thumb screws clockwise to
ensure proper grounding.
3 Connect one end of the touchscreen (RS232) cable to the rear side of
computer and the other to the LCD monitor. Tighten by turning the two
thumb screws clockwise to ensure proper grounding. (optional module)
4 Press the power button on rear panel to turn the monitor power on.
2-5
Installing the Driver Software
Elo TouchSystems provides driver software that allows your touchmonitor to
work with your computer. Drivers are located on the enclosed CD-ROM for the
following operating systems:
• Windows XP
• Windows 2000
• Windows Me
• Windows 98
• Windows 95
• Windows NT 4.0
Additional drivers and driver information for other operating systems (including
MS DOS, Windows 3.x, OS/2, Macintosh and Linux) are available on the Elo
Your Elo touchmonitor is plug-and-play compliant. Information on the video
capabilities of your touchmonitor is sent to your video display adapter when
Windows starts. If Windows detects your touchmonitor, follow the instructions
on the screen to install a generic plug-and-play monitor.
Refer to the appropriate following section for driver installation instructions.
2-6 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
Installing the Serial Touch Driver
Installing the Serial Touch Driver for Windows XP, 2000, Me,
95/98 and NT 4.0
NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the
driver.
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
2 If the AutoStart feature for your CD-ROM drive is active, the system
automatically detects the CD and starts the setup program.
3 Follow the directions on the screen to complete the driver setup for your
version of Windows.
4 If the AutoStart feature is not active:
5 Click Start > Run.
6 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
7 Click Open, then OK to run EloCd.exe.
8 Follow the directions on the screen to complete the driver setup for your
version of Windows.
2-7
Installing the Serial Touch Driver for MS-DOS and
Windows 3.1
You must have a DOS mouse driver (MOUSE.COM) installed for your mouse
if you wish to continue using your mouse along with your touchmonitor in
DOS.
To install Windows 3.x and MS-DOS from Windows 95/98, follow the
directions below:
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
2 From DOS, type d:\EloDos_W31 to change to the correct directory on the
CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
3 Type install and press Enter to start the installation.
4 Align the touchscreen.
You must have already completed Steps 1 and 2 before proceeding. Refer to
Chapter 2 of the Elo DOS and Windows Driver Guide as necessary for
additional installation information.
To run the INSTALL program:
1 Type INSTALL at the DOS prompt in the directory containing the driver
install files.
2 INSTALL asks you to select the software to install. Then choose
d:\EloDos_W31 from the displayed list.
3 INSTALL also asks you for the paths to use during installation, or you may
use its defaults. INSTALL creates directories as necessary, and warns you if
they exist.
If you are updating your software, you may wish to specify the paths containing
the earlier versions, and overwrite the obsolete files. All executable programs
are upward compatible. For a list of differences from each previous version of
the drivers, be sure to select "Differences from Previous Versions" during the
installation process.
INSTALL updates your AUTOEXEC.BAT file with the drivers you select.
INSTALL makes a copy of your original AUTOEXEC.BAT file, called
AUTOEXEC.OLD. If you already have Elo driver commands in your
AUTOEXEC.BAT file, they will be commented out.
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory
you specified. GO loads the touchscreen driver, runs the calibration program
ELOCALIB, and gives you some final instructions.
If you are using Windows 3.1, you will also calibrate the touchscreen within
Windows 3.1 with the Touchscreen Control Panel.
2-8 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
C H A P T E R
3
CHAPTER 3
OPERATION
About Touchmonitor Adjustments
Your touchmonitor will unlikely require adjustment. Variations in video output
and application may require adjustments to your touchmonitor to optimize the
quality of the display.
For best performance, your touchmonitor should be operating in native
resolution, that is 800x600 at 60-75 Hz. Use the Display control panel in
Windows to choose 800x600 resolution.
Operating in other resolutions will degrade video performance. For further
information, please refer to Appendix A.
All adjustments you make to the controls are automatically memorized. This
feature saves you from having to reset your choices every time you unplug or
power your touchmonitor off and on. If there is a power failure your
touchmonitor settings will not default to the factory specifications.
3-9
−
−
Control
Function
Turns the display system power on or off.
Power Switch
1
2
UP
Displays the OSD menus on the screen and used to
select (“Up” direction) the OSD control options on
the screen.
Displays the OSD menus on the screen and used to
select (“Down” direction) the OSD control options
on the screen.
Down
3
Adjusts the increasing value of the selected OSD
control option.
+
−
4
5
Adjusts the decreasing value of the selected
OSD control option.
3-10 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
CONNECTIONS ON UNDERSIDE
4
1
2
3
1 Power Connector Connect the power adapter.
2 Video Connector This can be connected with the D-sub 15 pin signal
connector.
3 Touchscreen connector This is for connecting the touch panel RS232
connector. (optional)
4 OSD Remote connector Connect the remote function key.
3-11
Controls and Adjustment
OSD Menu Functions
To Display and Select the OSD Functions:
1 Press
once to display the OSD function main menu.
UP
2 Press
a second time to select the different OSD control option.
DOWN
UP
DOWN
To Adjust the Value of the Control Option:
1 Pressing + / - button changes the value of the selected OSD control option.
UP
DOWN
After adjusting the values, the monitor will automatically save the changes
when user selected Save Exit.
UP
DOWN
NOTE: The OSD screen will disappear if no input activities are detected for 10 seconds.
3-12 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
OSD Control Options
OSD Menu
Brightness
• Adjust the brightness using + and − buttons.
Contrast
• Adjust the contrast using + and − buttons
Color
• Adjust the value of color gain (RED, GREEN, or BLUE) using + and - buttons.
Auto Tune
• Press + buttons to make LCD monitor adjust the related parameters
automatically for optimal display status.
3-13
OSD Menu
Qualtity (included Frequency, Phase, Track and Text/GRP)
Frequency
This item is used to decrease the vertical interference.
1 Select one display pattern from your computer.
2 Use + and − buttons on the LCD monitor to decrease the vertical interference
to get the optimal display.
Phase
This item is used to decrease the horizontal interference.
1 Select one display pattern from your computer.
2 Use + and − buttons on the LCD monitor to decrease the horizontal
interference to get the optimal display.
Track
Adjust the track using + and − buttons.
Text/GRP
Select “Text” or “GRP” display in special mode.
3-14 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
OSD Menu
OSD Menu
Position (included Horizontal and Vertical)
Horizontal
• Pressing + moves the display image to the right; Pressing − moves the display
image to the left.
Vertical
• Pressing + moves the display image upward; Pressing − moves the display
image downward.
Language (included ENGLISH, CHINESE, JAPANESE)
• Press + and - buttons to select English, Chinese and Japanese)
Recall
• Press + or - buttons to recall values.
Save Exit
• Pressing + or – buttons to save adjusting values and exit OSD menu.
Cancel Exit
• Pressing + or – buttons to cancel adjusting values and exit OSD menu.
3-15
3-16 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
C H A P T E R
4
CHAPTER 4
TROUBLESHOOTING
If you are experiencing trouble with your touchmonitor, refer to the following
table. If the problem persists, please contact your local dealer or our service
center.
Solutions to Common Problems
Problem
Suggestion(s)
The monitor does not respond
after you turn on the system.
Check that the monitor’s Power Switch is on.
Turn off the power and check the monitor’s power cord and signal cable
for proper connection.
Characters on the screen are dim Refer to the Controls and Adjustments section to adjust the brightness.
The screen is blank
During operation, the monitor screen may automatically turn off as a
result of the Power Saving feature. Press any key to see if the screen
reappears.
Refer to the Controls and Adjustments section to adjust the brightness.
Screen flashes when initialized
“Out of Range” display
Turn the monitor off then turn it on again.
check to see of the resolution of your computer is higher than that of the
LCD display.
Reconfigure the resolution of your computer to make it less than or equal
to 800x600. See Appendix A for more information on resolution.
Touch doesn’t work
Make sure cable is securely attached at both ends.
4-17
4-18 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
A P P E N D I X
A
CHAPTE
R
4
NATIVE RESOLUTION
The native resolution of a monitor is the resolution level at which the LCD
panel is designed to perform best. For the Elo LCD touchmonitor, the native
resolution is 800 x 600 for the 12.1 inch size. In almost all cases, screen images
look best when viewed at their native resolution. You can lower the resolution
setting of a monitor but not increase it.
Input Video
12.1" LCD
640x480 (VGA)
800x600 (SVGA)
Transforms input format to 800x600
Displays in Native Resolution
The native resolution of an LCD is the actual number of pixels horizontally in
the LCD by the number of pixels vertically in the LCD. LCD resolution is
usually represented by the following symbols:
640x480
VGA
800x600
SVGA
XGA
1024x768
1280x1024
1600x1200
SXGA
UXGA
A-19
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by
600 pixels vertically. Input video is also represented by the same terms. XGA
input video has a format of 1024 pixels horizontally by 768 pixels vertically.
When the input pixels contained in the video input format match the native
resolution of the panel, there is a one to one correspondence of mapping of input
video pixels to LCD pixels. As an example, the pixel in column 45 and row 26
of the input video is in column 45 and row 26 of the LCD. For the case when
the input video is at a lower resolution than the native resolution of the LCD, the
direct correspondence between the video pixels and the LCD pixels is lost. The
LCD controller can compute the correspondence between video pixels and LCD
pixels using algorithms contained on its controller. The accuracy of the
algorithms determines the fidelity of conversion of video pixels to LCD pixels.
Poor fidelity conversion can result in artifacts in the LCD displayed image such
as varying width characters.
A-20 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
A P P E N D I X
B
CHAPTE
R
4
TOUCHMONITOR SAFETY
This manual contains information that is important for the proper setup and
maintenance of your touchmonitor. Before setting up and powering on your new
touchmonitor, read through this manual, especially Chapter 2 (Installation), and
Chapter 3 (Operation).
1 To reduce the risk of electric shock, follow all safety notices and never open
the touchmonitor case.
2 Turn off the product before cleaning
3 Your new touchmonitor is equipped with a 3-wire, grounding power cord.
The power cord plug will only fit into a grounded outlet. Do not attempt to fit
the plug into an outlet that has not been configured for this purpose. Do not
use a damaged power cord. Use only the power cord that comes with your
Elo TouchSystems Touchmonitor. Use of an unauthorized power cord may
invalidate your warranty.
4 The slots located on the sides and top of the touchmonitor case are for
ventilation. Do not block or insert anything inside the ventilation slots.
5 It is important that your touchmonitor remains dry. Do not pour liquid into or
onto your touchmonitor. If your touchmonitor becomes wet do not attempt to
repair it yourself.
B-21
Care and Handling of Your Touchmonitor
The following tips will help keep your Elo Entuitive touchmonitor functioning
at the optimal level.
• To avoid risk of electric shock, do not disassemble the brick supply or
display unit cabinet. The unit is not user serviceable. Remember to unplug
the display unit from the power outlet before cleaning.
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do
not use thinner or benzene, abrasive cleaners or compressed air.
• To clean the display unit cabinet, use a cloth lightly dampened with a mild
detergent.
• Avoid getting liquids inside your touchmonitor. If liquid does get inside,
have a qualified service technician check it before you power it on again.
• Do not wipe the screen with a cloth or sponge that could scratch the surface.
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the
rag and wipe the touchscreen. Never apply the cleaner directly on the
touchscreen
B-22 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
A P P E N D I X
C
CHAPTER 4
TECHNICAL SPECIFICATIONS
Display Modes
Your Elo Entuitive touchmonitor is compatible with the following standard
video modes:
Item
Resolution Type
H. Scan(KHz)
V. Scan(Hz)
Pol.
1
640X350
640X350
720X400
720X400
640X480
640X480
640X480
640X480
800X600
800X600
800X600
800X600
800X600
VGA
31.469
37.861
31.469
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
70.087
85.080
70.087
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
+ / -
+ / -
- / +
- / +
- / -
2
VESA85
VGA
3
4
VESA85
VGA
5
6
VESA72
VESA75
VESA85
SVGA
- / -
7
- / -
8
- / -
9
+ / +
+ / +
+ / +
+ / +
+ / +
10
11
12
13
SVGA
VESA72
VESA75
SVGA
C-23
Touchmonitor Specifications
Model
ET1247L
12.1” TFT Active Matrix Panel
246(H) x 184.5(V) mm
LCD Display
Display Size
Pixel Pitch
0.3075(H) x 0.3075(V) mm
VGA 640 x 350 (70 / 85Hz)
VGA 720 x 400 (70 / 85Hz)
VGA 640 x 480 (60 / 72 / 75 / 85Hz)
SVGA 800 x 600 (56 / 60 / 72 / 75Hz)
SVGA 800 x 600
Display Mode
Max. Resolution
Contrast Ratio
Brightness
300 : 1 (typical)
2
2
300 Cd/m wo/touch; 275 Cd/m w/IT touch
50 ms (typ.) / 100 ms (max.)
262K
Response Time
Display Color
Viewing Angle
Input Signal
o
o
o
o
+60 ~ -60 (L/R), +40 ~ -50 (U/D) (typical)
Video
Sync
R.G.B. Analog 0.7V
peak to peak
TTL Positive or Negative
15 Pin Mini D-Sub
Signal Connector
Rear Control
Power on / off , Menu / Select (up, down),
Adjustment (+, -)
Brightness, Contrast, Contrast, Color, Auto Tune
H/V-Position, Frequency, Phase, Track, Text/GRP,
Mode Inf., Recall
OSD
DDC1 / 2B
Plug & Play
IntelliTouch
Touch Panel (optional)
Power Adapter
Input AC 100-240V, 50-60Hz, Output DC 12V/2.5A
(max.)
o
o
o
o
Temperature
Humidity
0 C ~ 50 C (41 F ~ 95 F)
20% ~ 85% (No Condensation)
To 10,000 Feet
Operating Conditions
Altitude
o
o
o
o
Temperature
Humidity
-20 C ~ 60 C (-4 F ~ 140 F)
5% ~ 95% (No Condensation)
242 x 302.5 x 60mm
Storage Conditions
Dimensions (HxWxD)
4Kg
Weight (Net)
Certifications
, TUV-BAUART, FCC, CE, C-Tick, MPR II and VCCI
C-24 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
AccuTouch Touchscreen Specifications
Mechanical
Top: Polyester with outside hard-surface coating with clear or
antiglare finish.
Construction
Inside: Transparent conductive coating.
Bottom: Glass substrate with uniform resistive coating. Top and
bottom layers separated by Elo-patented separator dots.
Standard deviation of error is less than 0.080 in. (2.03 mm). This
equates to less than 1%.
Positional Accuracy
More than 100,000 touchpoints/in² (15,500 touchpoints/cm²).
Typically less than 4 ounces (113 grams).
Touchpoint Density
Touch Activation Force
Surface Durability
Meets Taber Abrasion Test (ASTM D1044), CS-10F wheel, 500 g.
Meets pencil hardness 3H.
AccuTouch technology has been operationally tested to greater than
35 million touches in one location without failure, using a stylus
similar to a finger.
Expected Life
Performance
Optical
Typically 85% at 550-nm wavelength (visible light spectrum).
Light Transmission
(per ASTM D1003)
All measurements made using USAF 1951 Resolution Chart, under
30 X magnification, with test unit located approximately 1.5 in.
(38 mm) from surface of resolution chart.
Visual Resolution
Antiglare surface: 6:1 minimum.
Antiglare surface: Less than 15%.
Haze (per ASTM D1003)
Gloss (per ASTM D2457)
Antiglare surface: 90 20 gloss units tested on a hard-coated front
surface.
C-25
Mounting Options
Horizontal Mount
338
254+1
0
193+1
0
70
4X Customer Option
See Notes
C-26 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
Vertical Mount
245+1
0
70
193+1
0
338
C-27
No Bracket Mount
272
254+1
0
232
193+1
0
C-28 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
1
Centering Lip
Detail Centering Lip
Scale 2.0
192
26.4
60*
*Noted dimensions are for non-touch, AccuTouch,and IntelliTouch only.
For SecureTouch and Infrared add 3.5mm to each dimension
Notes for all Mounting Options
1. All drawing centers are the center of the viewable area.
2. LCD Panel Cutout dimensions in option 1 applies to all mounting options.
3. If customer kiosk material is wood:
4.5 holes thru for M4 screws with nuts, or no thru holes, screws for wood 4.
4. If customer kiosk material is sheet metal:
Concealed head threaded studs M4 with nuts
C-29
30 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
CHAPTER 4
REGULATORY INFORMATION
I. Electrical Safety Information:
A) Compliance is required with respect to the voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein will likely result in improper operation,
damage to the equipment or pose a fire hazard if the limitations are not followed.
B) There are no operator serviceable parts inside this equipment. There are hazard-
ous voltages generated by this equipment which constitute a safety hazard. Service
should be provided only by a qualified service technician.
C) This equipment is provided with a detachable power cord which has an integral
safety ground wire intended for connection to a grounded safety outlet.
1) Do not substitute the cord with other than the provided approved type.
Under no circumstances use an adapter plug to connect to a 2-wire outlet as
this will defeat the continuity of the grounding wire.
2) The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can
result in serious injury or death.
3) Contact a qualified electrician or the manufacturer if there are questions
about the installation prior to connecting the equipment to mains power.
II. Emissions and Immunity Information
A) Notice to Users in the United States: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
B) Notice to Users in Canada: This equipment complies with the Class B limits for
radio noise emissions from digital apparatus as established by the Radio Interfer-
ence Regulations of Industrie Canada.
C) Notice to Users in the European Union: Use only the provided power cords and
interconnecting cabling provided with the equipment. Substitution of provided
cords and cabling may compromise electrical safety or CE Mark Certification for
emissions or immunity as required by the following standards:
31
This Information Technology Equipment (ITE) is required to have a CE Mark
on the manufacturer’s label which means that the equipment has been tested
to the following Directives and Standards:
This equipment has been tested to the requirements for the CE Mark as
required by EMC Directive 89/336/EEC indicated in European Standard EN
55 022 Class B and the Low Voltage Directive 73/23/EEC as indicated in
European Standard EN 60 950.
D) General Information to all Users: This equipment generates, uses and can radi-
ate radio frequency energy. If not installed and used according to this manual the
equipment may cause interference with radio and television communications.
There is, however, no guarantee that interference will not occur in any particular
installation due to site-specific factors.
1) In order to meet emission and immunity requirements, the user must
observe the following:
a) Use only the provided I/O cables to connect this digital device with
any computer.
b) To ensure compliance, use only the provided manufacturer’s approved
line cord.
c) The user is cautioned that changes or modifications to the equipment
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2) If this equipment appears to cause interference with radio or television
reception, or any other device:
a) Verify as an emission source by turning the equipment off and on.
b) If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i) Move the digital device away from the affected receiver.
ii) Reposition (turn) the digital device with respect to the affected
receiver.
iii) Reorient the affected receiver’s antenna.
iv) Plug the digital device into a different AC outlet so the digital
device and the receiver are on different branch circuits.
v) Disconnect and remove any I/O cables that the digital device
does not use. (Unterminated I/O cables are a potential source of
high RF emission levels.)
vi) Plug the digital device into only a grounded outlet receptacle.
Do not use AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a
lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experi-
enced radio or television technician.
32 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
|